Pick the JuanaOne below about 3,000 pre-rolls a shift and a multichannel JuanaRoll above it. The JuanaOne lets one operator weigh, fill and compact up to 500 joints an hour in under 5 square feet. The JuanaRoll runs 1 to 8 automatic channels at up to 4,000 per channel per shift with two operators.
Between them sits the JuanaRoll-1, rated at 750 an hour. Below we compare the three Canapa pre roll machines on output, people, formats and floor space, then cover the used JuanaRoll 4 channel we have on the site.
How do the JuanaRoll and JuanaOne compare on output?
The JuanaRoll is rated at up to 4,000 pre-rolls an hour with 8 channels, eight times the JuanaOne's 500 an hour. Per person the gap is smaller: a JuanaOne yields up to 500 per operator hour, while an 8 channel JuanaRoll with two operators yields up to 2,000. These are Canapa's ratings.
- JuanaOne work center: one person, up to 500 an hour, under 5 square feet, weight cell dosing, bulk canister, 304 stainless steel.
- JuanaRoll-1: up to 750 an hour, EMFR weigh cell at 2/1000 g resolution, rotary cone dispensing, filling, compaction, tamping, twisting and trimming.
- JuanaRoll 4 channel: up to 2,000 an hour on the unit we list, two operators, 144 x 62 x 100 inches, 4,700 lb.
- JuanaRoll 8 channel: up to 4,000 an hour or 32,000 per 8 hour shift.
Discount every rating. One Canadian producer reported 3,000 an hour from an 8 channel JuanaRoll, about 75 percent of rating, and we plan all three machines at that ratio until a trial on your flower says otherwise.
Which pre roll setup fits your daily volume?
Under about 3,000 pre-rolls a shift, the JuanaOne fits; from 3,000 to 4,500, the JuanaRoll-1; above that, a multichannel JuanaRoll. Those bands are the ratings above at 75 percent over one 8 hour shift. A second shift doubles each band, which is often cheaper than the next machine up.
- Craft brand, 1,000 to 3,000 a day: one JuanaOne. It replaces hand weighing without a frame that sits idle half the day.
- Growing brand, 3,000 to 5,000 a day: a JuanaRoll-1, or two JuanaOnes if you want a backup lane.
- Mid volume, 5,000 to 10,000 a day: a 2 to 4 channel JuanaRoll.
- Wholesale or multi SKU, 10,000 to 24,000 a day: a 4 to 8 channel JuanaRoll.
Two JuanaOnes cost you two operators for about 1,000 an hour. A 4 channel JuanaRoll gets about twice that with the same two people. That crossover, somewhere around 5,000 a day, is where we stop recommending work centers.
A second JuanaOne shift adds 8 operator hours, about $147 at the $18.43 national median wage BLS reports for packaging machine operators, and roughly 3,000 more pre-rolls. That is under 5 cents a joint in direct labor, so we push small brands to fill a second shift before they buy a bigger frame. Run your own numbers in our pre-roll machine buying guide, which has the channel math and cost per joint.
How many people does each pre roll work center need?
A pre roll work center like the JuanaOne needs one dedicated operator per unit, because that person loads cones and runs every cycle. Canapa's launch release says a single person can weigh, fill and compact up to 500 joints an hour. A JuanaRoll needs two employees regardless of channel count.
Read that JuanaOne list carefully. It names weighing, filling and compaction. It does not list twisting or trimming, so ask how the tip is closed on the configuration you are quoted and who does it. If the answer is a second person with a twist tool, your labor per joint doubles.
The JuanaRoll-1 closes that gap. Canapa lists inline twisting and trimming on the JuanaRoll-1, plus camera cone verification before filling and an integrated PreCheQ check weigher. For a brand that wants a finished joint off one compact machine, it is the more complete single lane option.
Which Canapa pre roll machine handles more formats?
The multichannel JuanaRoll handles more formats at once, because each lane can be dedicated to a size or strain. The 4 channel unit we list runs 0.25 to 2 g and can run multiple strains at the same time or dedicate lanes to sizes without changing cone blocks. A JuanaOne runs one format at a time.
That matters for brands selling half gram multipacks next to 1 g singles. On a JuanaOne, every format change is a stop, a cone swap and a recipe change. On a JuanaRoll, two lanes can run halves while two run full grams, with unlimited recipes stored on the HMI.
Infused product is the other format question. The JuanaRoll we list is described as working with dry infused cannabis. Canapa's JuanaOne release does not address infused material, so test it with your own blend before buying. The JuanaOne does share its mechanical design with the JuanaRoll.
Are the JuanaRoll and JuanaOne NTEP certified?
Yes. Canapa reported in May 2023 that both received NTEP Certificates of Conformance in Accuracy Class II as automatic weighing systems, with certificate 23-022 for the JuanaRoll and 23-018 for the JuanaOne. At the request of a state Department of Agriculture, both carry a Category 3 event logger tied to operator or inspector.
That logger records every calibration, which is what an inspector will ask for. Our post on using NTEP event logs as an audit trail shows how to pull and keep those records. Confirm the certificate covers the exact configuration and software you buy.
Is a used JuanaRoll 4 channel worth it over a new JuanaOne?
A used JuanaRoll 4 channel is worth it if you will fill more than about 6,000 pre-rolls a shift within a year and have the floor and rigging for it. The unit we list is a 2022 build, serial 7605, prewired for added channels and rated at up to 2,000 an hour.
- Footprint: 144 x 62 x 100 inches and 4,700 lb, against under 5 square feet for a JuanaOne. Check door width, ceiling and slab before you commit.
- Growth path: prewired frames take added channels. A JuanaOne does not grow; you buy another one.
- Price: the used JuanaRoll 4 channel pre-roll machine is available at $140,000. Get a new JuanaOne or JuanaRoll-1 quote next to it and compare cost per joint, not sticker price.
- Trial: run a few hundred of your own cones through each lane and weigh a sample on a separate certified scale before you pay.
- Support: ATS completed its purchase of Paxiom in July 2024. Confirm parts and service coverage for a 2022 serial.
Our cannabis financial modeling team can run the payback on either path against your SKU plan. The full Canapa pre-roll and Paxiom packaging lineup we specify and supply is on the manufacturer page.
JuanaRoll vs JuanaOne FAQ
What is the difference between the JuanaOne and the JuanaRoll-1?
Both are single lane machines, but the JuanaRoll-1 is rated faster, at 750 an hour against 500, and Canapa lists inline twisting and trimming, rotary cone dispensing and camera cone verification on it. The JuanaOne launch release lists weighing, filling and compaction in under 5 square feet. Choose the JuanaOne for the smallest footprint and the JuanaRoll-1 for a closed joint.
How much floor space does a JuanaRoll need?
The 4 channel JuanaRoll on our listing measures 144 x 62 x 100 inches, about 12 feet by 5 feet, and weighs 4,700 lb. Add clearance on the operator side for cone and flower loading and at the discharge end for trays or a packing conveyor. Larger channel counts are longer, so get the drawing for your configuration from the quote.
Can a Canapa pre roll line feed automatic tube packing?
Yes. Canapa built its tube and tray loading systems to take product straight from the JuanaRoll, and its 2025 JuanaPack works alongside the JuanaRoll and the Vision360 inspector. The 2022 system could also be hand fed, so a JuanaOne room can still automate capping. Our packaging equipment guide covers how to lay out the line after the roller.
Tell us your daily target and sizes through the equipment request form and we will quote a JuanaOne, JuanaRoll-1 or multichannel JuanaRoll against it.