The NugSmasher Pro is a 20 ton press with 7 x 10 inch plates, six 160 watt heaters and a choice of pneumatic thumb control or a manual pump arm. It lists from $4,996 and is rated for up to 84 grams of flower per smash. Pneumatic work needs a 90 to 120 psi compressor with a 3 gallon tank.
This guide sticks to what NugSmasher publishes in its product page, owner's manual and extraction write ups. Where the factory gives no number, we tell you what to ask for in the quote.
What are the NugSmasher Pro specs?
The NugSmasher Pro delivers 20 tons of pressure through 7 x 10 x 1.5 inch plates, each plate carrying three 160 watt heating elements with its own digital controller. NugSmasher rates it at up to 84 grams of flower per smash and lists it from $4,996 product only, against a struck price of $7,500.
- Force: 20 tons, pneumatic or manual
- Plates: 7x10 plates, 1.5 inches thick
- Heat: six 160 watt elements, three per plate, dual digital temperature control
- Drive: thumb operated pneumatic control plus a manual pump arm
- Extras: LED lights and a cool down fan on manual switches, circuit protection, 6 foot power cable
- Air: compressor not included; 1/4 inch NPT inlet
- Price: from $4,996; bundles up to $14,032.09
- Warranty: listed as guaranteed for life, with 7 day factory support
The NugSmasher Pro product page also says the press can take up to a quarter pound of material at a time. That is a higher figure than 84 grams, so treat 84 grams of flower as the planning number and confirm hash loading with the factory.
If you are still choosing between the Pro and the smaller presses, our side by side of every NugSmasher model covers the Mini through the iQ Pro.
Is it a Pro or a Pro Touch?
The Pro Touch shares the 20 tons, 7 x 10 inch plates and six 160 watt elements, then adds a 10 inch capacitive touchscreen. NugSmasher listed it out of stock with no price in November 2026. On a used unit, the screen is the quick tell. The base Pro has a dual digital temperature display instead.
What air compressor does a pneumatic rosin press like the NugSmasher Pro need?
NugSmasher says any compressor with a working pressure of 90 to 120 psi and a 3 gallon or larger tank runs the Pro, with a water separator on the line. The owner's manual is a little tighter: it calls for a 3 to 5 gallon compressor and a minimum of 100 psi.
We would buy to the manual. A small 3 to 5 gallon unit that reaches 100 psi meets both statements, and NugSmasher publishes no CFM figure, so you do not need to size for a production air system. The Pro takes push connect airlines at labeled IN and OUT fittings.
Two things trip people up on install day. First, the compressor is not included, so it has to be on site before the press arrives. Second, moisture in shop air ends up in the line, which is why NugSmasher calls for the separator. If you want to skip air entirely, the Pro also runs by hand with the manual arm.
Plan where the compressor sits. A small compressor cycling at the bench is loud in a quiet extraction room, and a 6 foot power cable on the press limits how far you can move it from an outlet. Our facility design team lays out bench power and air drops with the equipment list in hand.
How do you convert gauge psi to plate pressure on the NugSmasher Pro?
The gauge on the NugSmasher Pro reads hydraulic pressure, not pressure on your bag. NugSmasher's manual converts between the two with a chart keyed to bag size: a single 14 gram bag at 750 psi on the material reads about 1,075 psi on the gauge.
The manual lists bag footprints, which drive the math:
- 3.5 gram bag: 1.5 inch diameter, 1.77 square inches
- 7 gram bag: 2 to 2.2 inch diameter, 3.14 square inches
- 14 gram bag: 2.4 to 2.7 inch diameter, 4.91 square inches
From the chart, one 14 gram bag reads 716 psi on the gauge at 500 psi on the material, 1,075 at 750 and 2,149 at 1,500. Load four 14 gram bags at 750 psi and the gauge target climbs to 4,298. The gauge number scales with total bag area, so a recipe written as a gauge reading only works for the same bag count.
The 20 ton ceiling still matters. Twenty tons is 40,000 pounds of force. Four 14 gram bags cover about 19.6 square inches, and at 1,500 psi on the material that is roughly 29,500 pounds, inside the limit. Spread across the full 70 square inch plate, though, 40,000 pounds is only about 571 psi.
NugSmasher's published runs give starting points. Its 14 gram Pro extraction write up pressed two 7 gram bags at 206°F, built to 1,375 to 2,292 psi on the gauge and held full pressure for about 90 seconds. Its single 7 gram, 160 micron run recommended 687 to 1,146 psi on the gauge. Those two ranges double cleanly with bag count, which matches the chart.
How much can a NugSmasher Pro press per shift?
NugSmasher does not publish a cycle time for the Pro, so throughput per shift is your loaded grams per press times the cycles your crew logs. At the rated 84 grams of flower, every 10 cycles is 840 grams, a little under 2 pounds.
Start the clock before the first press. The manual says the plates ship preset to 200°F and reach setpoint in about 10 to 12 minutes, so build warm up into the shift plan. For flower, the manual suggests starting around 220°F and dropping 5 to 7 degrees per test press until the result looks right.
The cycle itself is bag loading, the pressure build, the hold and collection. The 14 gram write up's 90 second hold is a floor, not the whole cycle. Time five real presses with your bags and material, average them, and use that number in the quote conversation.
For hash rosin, the press rarely sets the pace. The wash room and the dryer decide how much hash shows up at the bench, which is why our processing layout and equipment flow guide starts upstream of the press.
What should you check on a used NugSmasher Pro?
On a used rosin press, run the same acceptance tests you would on any heated hydraulic press: confirm the model, time the heat up, check plate temperature across both plates, build and hold pressure on a test load and read the warranty terms. NugSmasher's own manual sets the ground rules for the last item.
- Model and generation: confirm Pro or Pro Touch on the frame and ask for the purchase date and invoice.
- Heat up: the manual gives 10 to 12 minutes to the 200°F preset. Time it on both plates.
- Plate temperature: check the face of each plate at several points with a surface thermometer, since each plate runs three elements.
- Pressure: build to a known gauge reading on a test bag and watch that it holds through the hold step and returns on release.
- Release valve: the manual says never to open the release knob more than half a turn from tight; doing so voids the warranty and may result in hydraulic fluid loss.
- Casing: the manual says opening the casing or self repair voids the factory warranty, so ask whether anyone has been inside.
- Warranty transfer: ask NugSmasher directly whether coverage follows a resold unit. Factory refurbished units carry a 30 day warranty.
The NugSmasher Pro owner's manual is worth reading before you inspect, since it lists the setup order: release knob, joystick, airlines, manual handle, power, temperature, then compressor. Our guide to buying used extraction equipment covers the paperwork and landed cost side.
NugSmasher Pro FAQ
Can the NugSmasher Pro run without an air compressor?
Yes. The Pro has a manual pump arm in addition to its pneumatic thumb control, so an operator can build pressure by hand. NugSmasher's manual warns against pushing the handle down with a foot or any other device, which it says causes damage not covered by warranty. Pneumatic operation just takes the pumping effort off the operator during each cycle.
What temperature should I start at on a NugSmasher Pro?
The Pro ships with the plates preset to 200°F. NugSmasher's manual suggests starting flower around 220°F and lowering 5 to 7 degrees per test press. Its published 14 gram run used 206°F. Hash typically runs a different recipe than flower, so log temperature, gauge reading and hold time for every test and set your SOP from your own data.
How big are the bags that fit a NugSmasher Pro?
NugSmasher sells 3.5, 7 and 14 gram bags. The Pro manual lists their pressed footprints as 1.77, 3.14 and 4.91 square inches. A 7 x 10 inch plate has room for several bags per cycle, and the manual's chart shows gauge targets for one to four 14 gram bags at each material pressure.
Where can I buy or sell a used NugSmasher Pro?
Urth & Fyre does not stock NugSmasher today, but we source presses on request and quote condition, photos and freight before you commit. If you have a Pro you no longer run, list it through our sell equipment page. See the NugSmasher rosin press brand page for the full lineup and the rosin press and solventless equipment guide for washers and dryers.
Send your bag size, weekly hash volume and power details through a NugSmasher Pro sourcing request, or list a press you are retiring on our sell equipment page.