A used Anden dehumidifier is worth buying when the nameplate, amp draw, coil and drain check out. On an A710 V1, Anden's R-32 submittal lists 22.3 amps at 240 VAC. A unit drawing far off that, a fouled coil, an R-410A charge your tech cannot service or a missing A77 remote should cut the price or end the deal.
What should you check first on a used Anden dehumidifier?
Check the nameplate first on any used Anden dehumidifier: model, voltage version, refrigerant and serial number. Those four lines decide whether the unit fits your panel, whether your service tech can work on it and whether any warranty is left. Photograph the plate before you talk price, then match the model against our Anden dehumidifier and parts page.
- Model and version: V3 units run on 277 VAC. The A710 V1 takes 208 to 240 VAC, and the newer A711 and A321 V1 units take 208 to 230 VAC. A 277 VAC V3 does not belong on a 240 volt circuit.
- Refrigerant: Anden's A710 product information page marks the R-410A versions as discontinued and lists R-32 as current. Any A710 built before the switch carries R-410A.
- Serial number: Anden's technical support line is 1-877-420-1330. Call with the serial to confirm build date and warranty status before you pay a premium for remaining coverage.
- Year: Anden introduced the A710 with VLGR in November 2020, so an A710 will not predate that. The A321 and A711 were announced October 23, 2026, so used ones will be rare for a while.
If you are not sure which size the room needs, settle that first with our Anden dehumidifier models comparison. A clean used unit in the wrong size is still the wrong unit.
How do you check compressor amp draw on a used dehumidifier?
Run the unit under real load and clamp a meter on one leg of the supply. Then compare the reading to the rated draw. The A710 V1 submittal sheet lists 22.3 amps and 4,600 watts at 240 VAC, on a 30 amp breaker, rated at 80°F and 60 percent RH.
The test condition matters. A unit in a cold, dry warehouse will draw less than one running in a wet flower room, and the VLGR compressor backs off at low load by design. So test in a warm, humid space, or at least note the temperature and RH when you take the reading. A unit that trips its breaker, cycles on and off, or draws well above the rating has a problem you should price in.
Watch the defrost behavior while you are there. Anden's senior applications engineer, Randy Lenz, says the A710 defrosts about every two hours at 60°F and 50 percent RH. If a unit is defrosting far more often than that in similar conditions, we would want a refrigeration tech to look at it before purchase.
What do the coil and filter tell you?
The coil and filter tell you how the previous owner ran the room. Anden recommends replacing filters every 12 weeks or at the end of each harvest. If the filter is gray and sagging, assume it went months past that, and assume the coil caught what the filter missed.
Pull the filter and look at the coil face with a flashlight. You are looking for dust matting, bent fins, residue from foliar sprays and any corrosion. The A710 coil carries a factory I coat, so flaking or bare spots are worth a photo. A coil that needs a chemical cleaning is not a deal breaker; a coil with corrosion through the fins is.
- A710 filter: part 5852, MERV 11, 29.5 by 31.5 by 1.75 inches, MSRP $69.70.
- A321 and A711 filters: MERV 13 on the newer models.
- Budget: plan on a fresh filter before the unit goes into any room, used or not.
How do you check the condensate drain?
Check the drain by running the unit long enough to produce water and watching where it goes. The A710 drains through a 3/4 inch FNPT connection that needs a trap, and Anden ships a P trap and fittings with it. The A210V1 uses a positive pressure drain and needs no trap.
Look inside the drain pan and the first few inches of line for slime. Anden recommends cleaning the drain line between grow cycles with a diluted bleach or vinegar solution, then rinsing it. A unit that arrives with biofilm in the pan can carry contamination into your next room, so clean it before install. Our microbial mitigation work starts with drains like this one. Also confirm the float switch terminals work if the seller had an overflow switch wired in.
Who can service the refrigerant on a used unit?
Only an EPA certified technician should open the refrigerant circuit on a used Anden dehumidifier. Under EPA Section 608 rules, anyone who attaches gauges to measure system pressure or adds or removes refrigerant must hold certification, and that applies to dehumidifiers as much as rooftop units.
Tell your tech which refrigerant the nameplate shows before the visit. The two refrigerants are not interchangeable, and Anden lists the R-410A A710 as discontinued. On a used R-410A unit, factor in what a future leak repair will cost and whether your local service shop stocks it.
Does the Anden warranty transfer to a second owner?
Do not assume the warranty transfers to a second owner of a used Anden dehumidifier. Anden lists a 5 year warranty on the A710V3 covering all parts including the refrigeration system, and a 3 year limited warranty on the A321 and A711. Its legal terms say a customer may not assign rights under the agreement without Anden's consent, and installation is not warranted by Anden.
So confirm coverage with Anden by serial number, and get the answer in writing. If the seller cannot produce the original invoice and Anden will not confirm, price the unit as if it has no warranty left.
What should come with a used Anden dehumidifier?
A used Anden dehumidifier should come with the controller, the mounting hardware and the drain fittings it shipped with. Missing parts are cheap one at a time and annoying on install day. Here is the short list for an A710:
- A77 remote: reads RH at canopy height and relays diagnostics. MSRP $126.80 if you have to replace it.
- Mounting: ceiling brackets for a suspended install, or the adjustable feet for floor use. The A711 and A321 have integrated suspension points.
- Duct kit: part 5859, sold separately, if the unit was ducted from outside the room.
- Drain fittings and P trap: the 3/4 inch MNPT barb, female pipe adapter, tee and trap that ship with the A710.
- Cord: the A710 V1 uses a 10 foot L6-30P cord, with a hardwire option.
Rigging matters too. The A710 V1 cabinet weighs 360 lb, so plan two people and a lift for a suspended install. For a firsthand view of how the A710V3 behaves in a running room, read our A710V3 review from a working cultivator.
What is a fair price for a used Anden dehumidifier?
A fair price for a used Anden dehumidifier is current new price minus what you will spend to put it in service. Anden publishes MSRPs on some models: $3,377.78 for the A210V1 and $5,152.93 for the A320V3. Urth & Fyre recently sold a new 2024 A710V3 at $6,500, and that unit is sold.

From that starting point, subtract a filter, any missing remote or duct kit, a refrigerant check if the history is unknown and the warranty you are likely giving up. If those add up to more than a few hundred dollars on a 710 class unit, a new unit with 5 years of coverage starts to look better. Our post on new versus used cannabis equipment walks through that math across categories, and our cannabis HVAC design guide shows how each dehumidifier's heat lands on the room's cooling.
Used Anden Dehumidifier FAQ
Is a used Anden A710V3 worth buying?
It can be, if the nameplate shows the right voltage for your panel, the amp draw is near rating under load and the coil is clean. The A710V3 is rated at 710 pints per day and up to 3 liters per kWh. Price it against a new unit with a 5 year warranty, because that coverage may not follow the used one.
Where do you get parts for a used Anden dehumidifier?
Anden sells replacement filters, duct kits and controls by part number, and its A710 product information page links a service parts list and the product manual. For anything beyond filters, call Anden technical support at 1-877-420-1330 with the serial number so the parts match the refrigerant version.
How should you clean a used dehumidifier before it goes into a flower room?
Start with a new filter and a coil inspection. Flush the drain pan and line with a diluted bleach or vinegar solution, rinse thoroughly, and confirm the trap holds water. Wipe the cabinet interior, then run the unit in an empty room for a day and check the drain before plants go in.
If you want us to find a used or new Anden unit that matches your room, send the model, voltage and canopy area through our equipment request form. Selling one instead? List it on our sell equipment page with the nameplate photo.